ISO 9001:2008 CertifiedLOCK-N-STITCH, Inc. - CASTING Repair is Our Passion!
Casting repair products are eveloped and manufactured by LOCK-N-STITCH Inc.,the world leader in casting repair metal stitching technology. We use the latest state-of-the-art CNC machining and grinding equipment. We even manufacture our own special patented taps.
 | Shipping 
 | Tax 
 | Terms
 Request for Quote 0 Items
Casting Repair Products > Crack Repair Tools & Supplies > Stitching Pin Starter Kits > C Series Pin Mini-Kits > C Series Pin Mini-Kits > Order # LMK-C2F  
Download PDF Download PDF     Printable Page     Email Email This Page     Save To Favorites Save To Favorites

Order # LMK-C2F, C2F Steel Pin Mini-Kit










Specifications  · About C Series Stitching Pins

Specifications

Shipping Weight

65.44 oz

Pins

25 each of: C2FA, C2FB and C2FC
10 each of: C2FD and C2FE

Taps

1 each of C2FBT and C2FFT

Drill Bits

2 each of Accusize™ wire 7 drill bits

Other

1 each of C2F spotfacer
1 each of a drill stop for wire 7 drill bits and a drill stop for C2F spotfacer
1 ounce of tapping fluid for cast iron, steel and aluminum (L750)
20ml of heat-conductive sealant for steel stitching pins (LHC724)


About C Series Stitching Pins
CASTMASTER™ (C Series) stitching pins do not spread the crack! In fact they do the opposite. This pin with its incredible Spiralhook™ threads creates a drawing pressure that actually pulls the sides of a crack together and permanently locks them together. C Series pins exert PULLING pressure.

So why not just always use CASTMASTER™ pins? The installation process requires that every drilled hole receive a recessed spotface to assure some of the shoulder of the pin remains below the surface after grinding or machining. The spotfacing is accomplished with a special piloted tool. The reasons not to choose C Series pins for all your repairs are cost, speed and technical requirements. Because of the spotface, installing the pins at steep angles to the surface usually doesn't leave enough material thickness for the threads.

Almost all repairs to cylinder heads that are made below the seat angle are made with L Series pins. C Series pins can be used from the bottom of the seat angle outward to the end of the crack. A new seat can be ground or three-angle cut right on C Series or L Series pins. Cracks that extend back into a port are repaired by drilling through both walls. C Series pins will seal on both ends.

Cracks that run crosswise on the top of cylinder heads are usually repaired with CASTMASTER™ pins in order to add strength instead of spreading pressure, so the repair will not open when the head is torqued to the block. Cracks that extend from threaded holes, freeze plug holes, pipe plug holes and main bearing holes require CASTMASTER™ pins. Cracks that originate from the corner of the cap fit in a main bearing can be repaired with C Series pins.

You should always choose the largest diameter CASTMASTER™ pins that you can. For repairs in thin sections down to 0.100" use C1 pins. For sections starting at 0.200" in thickness, use C2F pins and for sections 0.750" to 2" use C3 pins.

C2 was the first CASTMASTER™ pin introduced and is now is being replaced with C2F pins. Many improvements, including one of the original design features, have been included in this new version. These changes include a single tap process for through holes, same tap drill size as L6 pins, a hook angle under the shoulder with matching spotface, ability to be used in thinner sections and a large increase in strength and seal.

In extreme structural repairs, locks should be used in conjunction with CASTMASTER™ pins. It is often easiest to use L Series pins next to the locks and then continue the repair with C Series pins.

Steel CASTMASTER™ pins can be used in aluminum castings where heat and corrosion are not a factor. Aluminum CASTMASTER™ pins should be used in combustion chambers when cracks extend below valve seat inserts and when the inserts will be replaced. When seat inserts will be replaced after a crack repair it is not necessary to heat the head and freeze the seat prior to installation. You can simply apply LHC623 to both the seat bore and seat and drive the seat in the way you would in a cast iron head. The sealant will lubricate during installation and then cure for retaining strength.

NOTE: The spotface depth for C Series pins is important. Whenever possible you should try for approximately 50% of the shoulder to be left below the surface. In the combustion chamber this will make the repair more heat-resistant. You must pay close attention to the depth of the spotface to make sure there is enough material left for threads.