Order # C2FE-25, Steel CASTMASTER® C2F Stitching Pins On Lock-N-Stitch


	Casting repair products are eveloped and manufactured by LOCK-N-STITCH Inc.,the world leader in casting repair metal stitching technology. We use the latest state-of-the-art CNC machining and grinding equipment. We even manufacture our own special patented taps.

		\| Shipping \| Tax \| Terms

Request for Quote	0 Items

Casting Repair Products > Crack Repair Tools & Supplies > Metal Stitching Pins > C Series Stitching Pins > C2F Stitching Pins > Steel CASTMASTER® C2F Stitching Pins > Order # C2FE-25


	Order # C2FE-25, Steel CASTMASTER® C2F Stitching Pins

Steel CASTMASTER® C2F Stitching Pins (C2FE)

larger image

Specifications · About C Series Stitching Pins

Specifications

Thread length		1 1/8 "

Material		Steel

Brands		CASTMASTER®

Major Diameter		0.234 '

Shoulder Diameter		0.280 '

Tap Drill Size		0.201" (wire size 7)

Thread Diameter		0.234 "

Units Per Package		25

About C Series Stitching Pins

CASTMASTER® (C Series) stitching pins do not spread the crack! In fact they do the opposite. This pin with its incredible Spiralhook™ threads creates a drawing pressure that actually pulls the sides of a crack together and permanently locks them together. C Series pins exert PULLING pressure.

So why not just always use CASTMASTER® pins? The installation process requires that every drilled hole receive a recessed spotface to assure some of the shoulder of the pin remains below the surface after grinding or machining. The spotfacing is accomplished with a special piloted tool. The reasons not to choose C Series pins for all your repairs are cost, speed and technical requirements. Because of the spotface, installing the pins at steep angles to the surface usually doesn't leave enough material thickness for the threads.

Almost all repairs to cylinder heads that are made below the seat angle are made with L Series pins. C Series pins can be used from the bottom of the seat angle outward to the end of the crack. A new seat can be ground or three-angle cut right on C Series or L Series pins. Cracks that extend back into a port are repaired by drilling through both walls. C Series pins will seal on both ends.

Cracks that run crosswise on the top of cylinder heads are usually repaired with CASTMASTER® pins in order to add strength instead of spreading pressure, so the repair will not open when the head is torqued to the block. Cracks that extend from threaded holes, freeze plug holes, pipe plug holes and main bearing holes require CASTMASTER® pins. Cracks that originate from the corner of the cap fit in a main bearing can be repaired with C Series pins.

You should always choose the largest diameter CASTMASTER® pins that you can. For repairs in thin sections down to 0.100" use C1 pins. For sections starting at 0.200" in thickness, use C2F pins and for sections 0.750" to 2" use C3 pins.

C2 was the first CASTMASTER® pin introduced and is now is being replaced with C2F pins. Many improvements, including one of the original design features, have been included in this new version. These changes include a single tap process for through holes, same tap drill size as L6 pins, a hook angle under the shoulder with matching spotface, ability to be used in thinner sections and a large increase in strength and seal.

In extreme structural repairs, locks should be used in conjunction with CASTMASTER® pins. It is often easiest to use L Series pins next to the locks and then continue the repair with C Series pins.

Steel CASTMASTER® pins can be used in aluminum castings where heat and corrosion are not a factor. Aluminum CASTMASTER® pins should be used in combustion chambers when cracks extend below valve seat inserts and when the inserts will be replaced. When seat inserts will be replaced after a crack repair it is not necessary to heat the head and freeze the seat prior to installation. You can simply apply LHC623 to both the seat bore and seat and drive the seat in the way you would in a cast iron head. The sealant will lubricate during installation and then cure for retaining strength.

NOTE: The spotface depth for C Series pins is important. Whenever possible you should try for approximately 50% of the shoulder to be left below the surface. In the combustion chamber this will make the repair more heat-resistant. You must pay close attention to the depth of the spotface to make sure there is enough material left for threads.

MORE IMAGES


	· C Series Stitching Pins

	· Pin, Drill and Tap Chart

Mini-Kit for C2 Stitching Pins



	LMK-C2F C2F Steel Pin Mini-Kit



	LMK-C2FL Aluminum C2F Mini-Kit

more available ..

Taps for C2F Stitching Pins



	Taps for C2F Stitching Pins

Drill Guide & Tap Extension for L6 and C2F Stitching Pins



	L6XK Drill Guide & Tap Extension Kit & Components

Tap Extractor & Fingers for L6 and C2F Taps



	L0060 Tap Extractors for L Series and CASTMASTER® Taps



	L0065 Tap Extractor Replacement Fingers for L Series and CASTMASTER® Taps (Set of 4)

Pin Spacing Drill Jig for L6 and C2F Stitching Pins



	L6500 Pin Spacing Drill Jigs

Quick Change Adapter for L6 and C2F Taps



	C2TA Quick Change Tap Adapters

Order # C2FE-25, Steel CASTMASTER® C2F Stitching Pins

Thread length

Material

Brands

Major Diameter

Shoulder Diameter

Tap Drill Size

Thread Diameter

Units Per Package